Audi A6 Owners & Service Manuals
Audi A6 Typ 4G (2011–2018) Workshop Manual / Body / Body Interior / Interior Equipment / Center Console Rear Trim, Removing and Installing

Audi A6 Typ 4G: Center Console Rear Trim, Removing and Installing

Center Console Rear Trim, Removing and Installing

Special tools and workshop equipment required

  • Wedge Set -T10383-
  • Hook Tool -T40207-

Removing

  Note

The vent has a hole on both sides for attaching the Hook Tool -T40207-.

- Carefully insert the Hook Tool -T40207- between the slats and hook it into the side of the vent.

- Alternating between the sides, carefully remove the vent -1- from the installation opening in direction of -arrow-.

- Disconnect the connector and remove vent.

A68-10547

- Remove the bolts -1-.

- Carefully unclip the cover -2- at the sides starting at the top using the Wedge Set -T10383/1--arrows-.

- Remove the cover toward the rear from the center console.

- Disconnect the connectors.

A68-10467

Market-Specific

- Open the retainers in direction of -arrows A- and push the air duct -1- slightly down.

- Remove the left and right bolts -2-.

- Carefully unclip the cover -3- at the sides starting at the top using the Wedge Set -T10383/1- in direction of -arrows B-.

- Remove the cover toward the rear from the center console.

- Disconnect the connectors.

A68-10648

Switch/Regulator/Storage Compartment Trim, Removing and Installing

Special tools and workshop equipment required

  • Wedge Set -T10383-

Removing

- Carefully unclip the cover -1- from the center console using the Wedge Set -T10383/1--arrow- and remove with the switch.

- Disconnect the connector for the switch/regulator.

Installing

Install in reverse order of removal. Note the following:

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Center Console".

A68-10544

Center Console Cover, Removing and Installing

Removing

- Remove the center console. Refer to → Chapter "Center Console, Removing and Installing".

- Remove the bolts -1 through 8- and remove the center console cover -9-.

Installing

Install in reverse order of removal. Note the following:

- Tighten the bolts in a -1 through 8- sequence.

Installation notes, for example tightening specifications, replacing components. Refer to → Chapter "Overview - Center Console".

A68-10472

    READ NEXT:

     Center Console Insert, Removing and Installing

    Special tools and workshop equipment required Trim Removal Wedge -3409- Removing - Versions with a selector lever: move the selector lever into "D/S". - Turn off the ignition. - Li

     Cupholder, Removing and Installing

    Cupholder, Removing and Installing Removing - Remove the center console. Refer to → Chapter "Center Console, Removing and Installing". - Remove the storage compartment in the center

     Overview - Front Center Armrest

    1 - Bracket For the center armrest Removing and installing. Refer to → Chapter "Center Console Bracket, Removing and Installing". 2 - Rear Trim For the center armre

    SEE MORE:

     Anti-Theft Alarm System

    Overview - Interior Monitoring Overview - Interior Monitoring, Sedan 1 - Alarm Horn -H12- Removing and installing. Refer to → Chapter "Alarm Horn -H12-, Removing and Installing". 2 - Nut 3 Nm 3 - Bracket For Alarm Horn -H12- 4 - Nut 3 Nm

     Seat Adjustment Control Head, Removing and Installing

    Special tools and workshop equipment required Trim Removal Wedge -3409- Removing - Carefully pry the actuator -1- using the Trim Removal Wedge -3409- from the retainer. - Repeat the process on the opposite side of the gap cover. - Repeat the procedure for the second actuator. -&n

    © 2011-2026 Copyright www.aa6.tochrfr.com