Audi A6 Typ 4G: Seat Frames
- Overview - Seat Versions
- Component Location Overview - Electric and Electronic Components
- Overview - Front Seat
- Overview - Front Backrest
- Overview - Headrest
- Overview - Seat Pan, Modular Wiring Routing
- Overview - Seat Pan, Seat Angle Adjuster
- Overview - Seat Pan, Seat Adjustment Actuator/Switch
- Front Seat, Removing and Installing
- Seat Height Adjuster Handle, Removing and Installing
- Seat Angle Adjuster, Removing and Installing
- Backrest Adjuster, Removing and Installing
- Front Backrest, Removing and Installing
- Backrest Cover, Removing and Installing
- Spring Mat, Removing and Installing
- Front Seat Wire Routing
- Seat Side Trim on the Tunnel Side, Removing and Installing
- Seat Forward/Back Adjustment, Servicing
- Upper Seat Frame, Removing and Installing
- Storage Compartment, Removing and Installing
- Seat Adjustment Control Head, Removing and Installing
- Front Seat Control Module Bracket, Removing and Installing
- Overview - Seat Bench/Single Seat
- Overview - Locking Mechanism
- Overview - Headrest and Headrest Guide
- Overview - Rear Seat Backrest
- Overview - Center Armrest
- Seat Bench/Single Seat, Removing and Installing
- Center Storage Compartment, Removing and Installing
- Lock Cylinder, Removing and Installing
- Headrest, Removing and Installing
- Rear Seat Backrest, Removing and Installing
- Rear Seat Backrest Locking Mechanism, Removing and Installing
- Center Armrest, Removing and Installing
- Overview - Front Seat Pneumatic System
- Connection Diagram - Front Seat Pneumatic System
- Overview - Front Seat Pneumatic System, Compressor
- Overview - Front Seat Pneumatic System, Backrest
- Preparations for Checking the Seat Bolster Adjuster for Leaks, through
08/2012
- Preparations for Checking the Backrest Bolster Inflation Adjustment for
Leaks, through 08/2012
- Preparations for Checking the Massage Mat Air Cushion for Leaks, from
09/2012
- Compressor/Multi-contour Seat Control Module, Removing and Installing
- Module Carrier with Air Cushions for Lumbar Support, Removing and Installing
- Multi-contour Seat Valve Block, Removing and Installing
- Massage Mat, Removing and Installing
- Overview - Rear Seat Pneumatic System
- Rear Seat Pneumatic System, Checking
- Air Cushion for Lumbar Support, Removing and Installing
READ NEXT:
Component Location Overview - Seat Versions
Note
In the illustration, seats in a sedan model with a fixed backrest is
shown.
1 - Front Passenger Seat
Standard seat/Sport seat/Supe
Component Locations Overview - Electric and Electronic Components,
Standard Seat/Sport Seat/Super Sport Seat
1 - Driver Seat Angle Adjustment Motor -V243-
Front passenger side: Front Pa
Overview - Front Seat, Standard Seat/Sport Seat
Standard Seat/Sport Seat (Manual)
1 - Connector Station
Connector assignment. Refer to
→ Wiring diagrams, Troubleshooting & Co
SEE MORE:
Special tools and workshop equipment
required
Roller -3356-
Adhesive Strip Remover -VAS6349-
Gauge - Gap Adjustment -3371-
Front and Rear Door Template -T40038/8-
Inner Door Seal, Removing and Installing
1 - Inner Door Seal
"B-pillar" upper trim removed.
The lower A-pillar and
Brake Rotor, Removing and Installing, Steel Brakes
Special tools and workshop equipment
required
Torque Wrench 1331 5-50Nm -VAG1331-
Removing
- If the same brake rotor is reinstalled with used brake pads,
remove the brake caliper. Refer to
→ Chapter "Brake Caliper, Removing and Ins
